Skip to main content

Commercial and industrial electrical, Cleveland and the west side

Three-phase service and panel work for Cleveland, drawn to spec.

Load calculations, three-phase service and panel work for Cleveland shops, warehouses and tenant build-outs, documented to spec and handed over as drawings at closeout.

Hours

Mon to Sat, 7am to 7pm, and emergencies any hour

Service area

Cleveland

Established

2009

Northgate Electrical Contractors

Why Us

Four Reasons to Book with Confidence.

Every job, every customer. These don't change.
  1. Licensed Electricians State-licensed, every job
  2. Permit & Inspection We pull it and we meet it
  3. 24/7 Emergency Someone answers at 3am
  4. Upfront Pricing Quoted before we start
Emergency Service

Power Out or Sparking? Start Here.

Sparking panels, dead outlets, smoke from a wall switch. Turn the breaker off if you can do it safely, then call.
Call and tell us what you see.
Smoke or Burning Smell From an outlet, switch, or panel. Kill the power at the panel if you can do it safely, then call.
Sparking or Buzzing Panel Audible humming, sparks, or warm breakers mean a fault is escalating.
Total Power Loss Whole-home outage with neighbors still lit means it's on your side of the meter.

Electrical Services

What We Do

Commercial service, panels and fit-outs, drawn and submitted to spec.

Mark Description From

Commercial Service & Panels

New service entrances, 400A to 800A panels, and sub-panels sized from a real load calculation, not a guess. As-built drawings handed over at closeout.

from $3,500

Three-Phase Power

Three-phase distribution for shops, machines, and HVAC. We map the loads, size the feeders, and label every circuit so the next tech isn't guessing.

from $2,800

Industrial Wiring & Controls

Conduit runs, motor circuits, and control wiring installed to the diagram and tagged to match. Clean panel schedules you can actually read.

from $2,200

Tenant Fit-Outs

Build-out electrical for offices, retail, and restaurants, coordinated with your GC and inspector so you open on schedule.

from $1,800

Load Studies & Code Corrections

Failed an inspection or planning new equipment? We run the numbers, document the fix, and bring the system back into code.

from $450

Permits & Inspections

What Needs a Permit

Panel work, EV chargers and service changes usually need one.
Permits In Your Estimate
Ask whether your job needs a permit and what the inspection involves.
How It Works

Simple Start to Finish

What happens from your first call to the final walkthrough.
  1. Reach Out Anytime

    Describe your issue or project online or by phone. We'll schedule your consultation and confirm a time that works.
  2. Get a Clear Estimate

    We inspect your setup, explain every option, and put the estimate in writing.
  3. We Do the Work

    We do the agreed work and walk you through what changed before we leave.
  4. Walk Away Confident

    We finish, test and walk you through the work.

Trusted Brands

Brands We Install

The brands we install and service.

Generac PowerPRO Dealer
Tesla Certified Installer
ChargePoint Installer
Kohler Generator Dealer
Coverage

Areas We Serve

We work in the towns listed here. If yours isn't on the list, call and ask.
  1. Cleveland
  2. Lakewood
  3. Parma
  4. Euclid
Request a bid

From Businesses We've Wired

Property managers, builders, and shop owners who needed the work done right and the paperwork to match.

★★★★★
Northgate upgraded our shop to three-phase and labeled every circuit on a clean panel schedule. First electrician we've used who handed over drawings that actually match the install.

Greg H.

★★★★★
They ran the load calc before our tenant fit-out and caught that the existing service was undersized. Saved us a failed inspection and a change order down the line.

Sandra L.

★★★★★
Replaced an 800A service for our warehouse with zero downtime, scheduled it around our shifts, and the as-built set was waiting at closeout. Exactly what a commercial job should be.

Tomás V.

FAQ

Common Questions

Everything you need to know before hiring an electrician, answered honestly.
Ask a Question
Do you pull permits?
Ask us about permits for your job. Panel work, EV chargers and service changes usually need one, and we'll tell you what's involved before we start.
Do you offer financing?
Ask when you get your estimate and we'll tell you what payment options are available for the work.
What happens on the first visit?
We look at the work, talk through the options, and put the price in writing before anything gets switched off.
Do you clean up afterward?
Yes. Cover plates go back on, drop cloths come up, and every scrap of wire leaves with us.
Spec Sheet

Ready to Wire It Right?

Let's Get Your Project Started

Tell us what you need and we'll get back to you with a detailed estimate.

We reply about your request.

Your details go only to this business. Data handled by Buildrok.

Electrician Website Template by Buildrok
Call Now Text